HOUSE: Newburgh

ENJE roller shades.

I’ve had a lot of problems getting the curtain/shade/blind (I hate the term “window treatment”—it makes me think of a gigantic box valance) situation in our house where it should be. Six-inch casings, non-standard sizes, 10′ ceilings, and curved walls with side-by-side windows make everything a challenge. The cost of custom-made shades freaks me out, and with 14 windows, it’s just not going to happen.

I love the way the old windows look without anything covering them, but that’s not practical in every room of the house. In the office at the back of the house, there’s no need for privacy, but the “reflective black hole” effect at night is a little creepy.

Enter the ENJE roller blind from IKEA. $24.99, attractive metal hardware, sheer enough to allow full daylight to pass through, opaque enough to keep glare (and the black hole) away, and with a margin large enough that the window sashes show on all four sides even with the blind fully closed. Yay! Let’s buy a hundred of them!

Perfect, yes, except for the part where they come in five sizes, none of which will fit any of our windows. Sigh.

BUT WAIT!!! A little Googling showed me that not only can they be trimmed, but they look really good after doing so. Aided with a metal blade in the jigsaw, good-quality fabric shears, a straight edge, and some good advice from Morgan at The Brick House, I was able to alter two shades to fit my windows perfectly, and it only took about 30 minutes.

See? They even let in the scraps of daylight hanging around at dusk.

I wound up cutting the top roller and bottom rod separately (I removed it first), then verrrrry carefully cutting the fabric the full length of the shade. I cannot stress enough the importance of using a good quality pair of shears to do this! Hopefully you have scissors in your house reserved exclusively for cutting fabric. And you NEVER EVER cut paper or anything else with them. Right? Right. That’s what you should use to cut the shade. Not the grimy Fiskars in your junk drawer. Cut slooooowly and evenly, following the line you drew in ever-so-faintly with a hard pencil after measuring carefully. Slide the bottom rod back on, roll up, and you’re all set.

Previous Post Next Post

Other Stuff You Might Be Into

49 Comments

  • Reply erika April 9, 2009 at 10:10 pm

    beautiful! that’s not an easy task. looks great.

  • Reply Anna at D16 April 9, 2009 at 10:13 pm

    It was actually really simple! Using a jigsaw to cut the metal rods makes the whole thing take 15 minutes per shade, tops. The most time-consuming part was measuring/marking the cut line.

  • Reply erika April 9, 2009 at 10:26 pm

    i meant finding the perfect fit for your space. i’m glad the process was easy once you found just the right shade though. i’m on the hunt myself, there are no ikeas in colorado. *sigh*

  • Reply Anna at D16 April 9, 2009 at 10:32 pm

    I’m not sure I could survive without an IKEA an hour away. You have my sympathies!

  • Reply grace April 9, 2009 at 10:43 pm

    i posted the original question on ikeafans that you referenced! i never got around to shortening them, though. is this the internet’s way of reminding me that i’ve been putting it off for almost two years(!)? surely it’s a sign that i have to do it this weekend. would you mind sharing the extra tips that you were given?

  • Reply maya April 9, 2009 at 10:58 pm

    Yay Anna,
    Yay Morgan,
    my two favorite bloggers! double yay!

  • Reply the brick house April 9, 2009 at 11:01 pm

    looks rad. great job.

    Ikea is endlessly useful for those with a need to customize on a budget.

    Maya, your my favorite person.

  • Reply the seventy tree April 10, 2009 at 6:11 am

    The blinds look fantastic! I’m completely with you on ‘window treatments’ and scary black holes at night!
    Kerry.

  • Reply jenny April 10, 2009 at 8:17 am

    brilliant Anna!

  • Reply Jenn April 10, 2009 at 8:37 am

    Another solution to the ‘black hole effect’ is landscape lighting. Softly uplighting a tree in the backyard (if you have a backyard) is inexpensive, especially if you use a solar light, and expands the nighttime view.

  • Reply jones April 10, 2009 at 9:25 am

    Great solution. However, if you did require privacy would you say that this blind is too sheer?

    Thanks

  • Reply katie April 10, 2009 at 9:37 am

    sigh, i wish that ikea wasn’t so far away, i too need blinds of some sort that are a custom size. we went to penneys last week just to see how much a custom natural (bamboo?) blind would be and the price was… over $1k! for one window! from jcpenneys! yikes. i love how these roller shades look in your room though, and i like how they don’t completely block the light but still seem to provide privacy. it looks like even these roller shades would not be wide enough for me though. guess i’ll keep looking…

  • Reply Anna at D16 April 10, 2009 at 10:08 am

    grace: What?! Really? Wow, that is kind of weird. And yes, it’s a sign that you need to cut those shades this weekend! Beyond what I wrote in the post, the only other suggestion I would offer would be to remove the bottom rod first, measure the cut line on the top roller, then snip into the fabric horizontally up to the cut line. Then you’ll be able to fold the fabric back while you saw the top roller. Does that make sense?

    Jenn: I do have a garden, but our house is an attached row house on a city lot. Putting any kind of lighting in my backyard at night would be just plain evil to my neighbors! I had a downstairs neighbor in Brooklyn who had landscape lighting, and it was REALLY ANNOYING at night — we needed blackout shades to be able to sleep.

    jones: Yes, they are too sheer to really provide good privacy at night. Fine for the back of my house, but I wouldn’t use them on the street side on the first floor.

  • Reply Kelly April 10, 2009 at 10:24 am

    oooh, i’m loving the lighting effects these shade create! great choice.

    xo
    kelly

  • Reply mommy April 10, 2009 at 10:41 am

    Looks wonderful, Anna! I’m wondering if after you cut the width, do you need to bond the edges in some way?

    I’m glad I read Jenn’s comment as solar lights might be a good solution for our horrendous bare-window black holes. I’ve noticed how much nicer it looks inside at night if the (wasteful) porch lights are on.

    Speaking of IKEA, I just finished putting together the sofa and two chairs for our basement room – it was so easy! It was kind of satisfying to know exactly how they were made and assembled. They seem like sturdy pieces and the slipcovers fit perfectly, unlike the one for our Room & Board chair, which is too big and doesn’t have any velcro to keep it in place, like the IKEA ones. Does anyone know if it’s okay to wash the large sofa slipcover in a regular washing machine, or will it get too wrinkled?

  • Reply unha April 10, 2009 at 11:12 am

    funny about the scissors. my mom is an textile artist. as i was growing up, we had box of scissors that my dad and i were forbidden to touch (not even LOOK, especially if I was looking for a scissor), even in the case of emergency. those were for her fabrics, and ONLY that!

  • Reply theresa April 10, 2009 at 11:46 am

    I wanted to buy these for our windows, but the widest ones IKEA makes are only 55″ and our windows are at least 70″ wide…if I could only turn them sideways! We ended up buying solar shades which cost $600 for 3 windows. Ridiculous.

  • Reply lindsay April 10, 2009 at 12:10 pm

    I’ve just recently bought proper fabric scissors. At $75, they will not be touching paper, EVER. They do cut like a dream. And it only took me 29 years to realize one should have more than one pair of scissors…

  • Reply Ricky April 10, 2009 at 12:11 pm

    It might be easier to use a rotary cutter than a pair of scissors. You put it next to a straight edge and cut. I suggest cutting on the waste side. If you slip, no big deal.

  • Reply Dewi April 10, 2009 at 12:23 pm

    Nice shades!
    You could do a whole post on the virtues of the right scissors and correct equipment, how it makes project a 100% easier.

    My sister (a sewer extraordinaire) gave me a pair pair of beautiful fabric scissors for a birthday gift.

  • Reply Shashi April 10, 2009 at 12:32 pm

    wow, makes me want to switch out the disgusting blinds that came with our house.

  • Reply Kiley April 10, 2009 at 12:51 pm

    This is off topic, but I was browsing Apartment Therapy and saw your room! How lovely. http://www.apartmenttherapy.com/chicago/inspiration/colorful-book-nooks-081621

  • Reply Anna at D16 April 10, 2009 at 1:03 pm

    mommy: Nope, no need to bond the edge! The fabric feels like it already has some kind of coating on it. There’s NO fraying at all.

    As for the slipcover, I used to put the one for my old IKEA sofa (cotton/poly blend) in the washing machine with no problem, but I don’t know about the 100% cotton ones. I would imagine if you take it out right away and hang to dry it would be fine, especially since it gets stretched so tightly around the body of the sofa.

    Ricky: You’d need a pretty gigantic cutting table in order to make the rotary cutter useful though, right? The shades are 98″ long. I’ve never used a rotary cutter before, but don’t you have to have a stable surface underneath?

  • Reply Jennifer April 10, 2009 at 5:47 pm

    I’m glad that I’m not the only one who finds the “reflective black hole” effect creepy. Although I actually have a fear of it that dates back to my childhood. I feel really grown up when I’m afraid to go in a room alone because of it.

  • Reply alex April 11, 2009 at 1:42 am

    Hi, really love your blog.
    I had a question; where did you get that white floor lamp in your living room?

  • Reply Anna at D16 April 11, 2009 at 2:37 am

    alex: Thanks! I bought the lamp at West Elm several years ago — unfortunately, they don’t carry it any longer.

  • Reply Franziska April 12, 2009 at 1:22 am

    very cool idea. We also don’t have custom windows. Thanks for the great tip!

  • Reply Tatyana April 13, 2009 at 11:03 am

    Last time I was at IKEA, I saw these shades and thought I should get them for our place. I really liked the metal “rod” at the bottom and the chain. I could just buy them and try them but our closes IKEA is 2.5 hours away and I’m not up for multiple trips.
    Our neighbors are really close to us and I feel we have no privacy at all but I love the light that we get when the blinds we have up now are open. Do these block a lot of light? You said they are sheer – would we at least get privacy during the day? I was thinking about adding darker curtains for privacy at night. Ah… questions, questions, questions…

  • Reply Anna at D16 April 13, 2009 at 11:31 am

    Tatyana: Yes, they would give you privacy during the day (unless you were right next to the window), absolutely. At night you can see through if the lights are on.

    Have you considered using frosting film on your windows? We used it in both of our bathrooms, and it provides very good privacy while still letting in full, diffused light.

  • Reply Ricky April 13, 2009 at 1:45 pm

    Yes, you do need a stable surface, but it could be a table, a countertop, or even the floor. You also need a cutting board, preferably a self healing board. Just mark as you did for using a scissor, then line the straight edge up and cut. Keep moving the straight edge along the line, folding and unfolding the length of fabric as you go. Once you get use to the the rotary cutter, it’s really easy to get great results.

  • Reply Tatyana April 13, 2009 at 2:43 pm

    Thanks Anna. I would love to frost the bottom half of windows – so I could have a view but also privacy – and no “window treatment” at all. But, we live in an association and they don’t allow it. 🙁
    I can’t wait to own a house where I can do whatever I want to.
    I think I’m going to get the same blind you did only for the bathroom for now. I can always have another excuse to go to IKEA to get the rest.

  • Reply jones April 13, 2009 at 3:02 pm

    Thanks for the reply. good to know. window coverings are so tricky.

    I came across this pillow and immediately thought of you:

    http://www.etsy.com/view_listing.php?ref=vl_other_1&listing_id=23307123

  • Reply Anna at D16 April 13, 2009 at 3:38 pm

    *GASP* THAT PILLOW!!!!!!!!!!!!!!!

    Thank you thank you thank you…

  • Reply jones April 13, 2009 at 5:25 pm

    you’re welcome!

  • Reply Kristina April 15, 2009 at 10:22 am

    Those blinds are sheer, I guess. I used to have them in my Brooklyn kitchen and still walked around in my underwear. I was neither pelted, nor was there a crowd gathering, so it couldn’t have been that bad? I loved those blinds! Wish they were super wide for my super large windows in the ‘burbs.

  • Reply kristin April 16, 2009 at 11:27 am

    First off – your site is amazing. You are a total home-design inspiration.

    I love these blinds! I have them in 2 windows (where they almost fit): I love how they disappear when they’re not in use, and provide a soft filter when down. I’ve wanted them on a few of my other 100-year old windows, but haven’t felt the gumption to try altering them.

    One question – how did you remove & reattach the bottom rod? The rod from the shades I that got about 5 years ago do not seem to come off.

    Thanks again for all these awesome posts!

  • Reply kristin April 16, 2009 at 11:29 am

    { Oops – “that I got’ – I meant. Brain and hands don’t always work in concord.}

  • Reply jennifer July 18, 2009 at 9:56 am

    Hi – have kept this post as “new” in my RSS feed for forever as I knew I would get to it at some point. Am having the same issue as Kristin, above – any tips on how to remove and re-attach the bottom rod? have fiddled a bit and can’t find a an easy solution. any tips would be great. thanks!!

  • Reply Anna at D16 July 18, 2009 at 10:07 am

    Jennifer, just pull the end cap off and the the shade will slide right out of the rod.

  • Reply Jennifer July 18, 2009 at 7:41 pm

    Anna – thank you! I think was so afraid of breaking that I just wasn’t pulling hard enough/at the right angle. Success – pieces apart, will cut tomorrow. On a side note – also love your blog for the Morrissey entries!

  • Reply jessica October 11, 2009 at 12:00 pm

    very informative blog post! I have been looking for economical roller shades…..did you use a hacksaw?

    btw-how was the Furs show?

    -jessica

  • Reply Anna at D16 October 11, 2009 at 4:00 pm

    I used a metal-cutting blade on a circular saw, but a hacksaw would work just fine.

    Furs = awesome as always!

  • Reply kristin October 18, 2009 at 8:25 pm

    Thanks, Anna!

    Still haven’t gotten it together to custom size these (I commented way back in April — LA-ZY!), but I’m planning to try it this week: new neighbors just moved into the apartment 10 feet away, and I need to be a bit more neighborly. Thank you for all your awesomeness!

    (I intend on making that chili you just reposted, too. Mmmm! It sounds great. It is definitely chili weather here in Chicago…)

  • Reply Megan November 16, 2009 at 3:29 pm

    I love the look of these blinds too– but I also have a window that is too wide.

    That got me thinking though– do you think that you could put multiple blinds on one rod? IKEA’s online pictures aren’t great so I can’t really see the cord mechanisms… but could it be tweaked? And could it be done so that each could still operate independently?

    And most importantly, how weird would it look? 🙂

  • Reply Tracy February 24, 2010 at 12:44 am

    Hi Anna,

    I hope this is not a silly question: what is the brand/model of your fabric shears? I am moving to my new place soon & need 8-10 Enje blinds for the whole house. I am a person out of DIY technique and hope a gd pair of scissors could save me from hell.

    I know you heard it many times before, but I still want to say: I LOVE LOVE LOVE your house (esp the white painted wood floors).

    TIA.

  • Reply Anna at D16 February 24, 2010 at 8:15 am

    I don’t have them handy, but I’m pretty sure they’re Fiskars. Any fabric shears should be fine — just make sure you NEVER use them for cutting anything other than fabric. (And make sure everyone else in your house respects that rule!)

  • Reply richard November 11, 2012 at 1:11 pm

    so far, i have hung 5 of these shades & only two actually rollup the way they are supposed to. the other three somehow have become “sprung” or something. I like the way they look once up, but i hate the way they work, which is not.

  • Reply louize September 8, 2013 at 12:07 pm

    I have had these blinds in the back of my mind for years – probably since you or Morgan first posted about them way back when, and now I have windows where they make sense/I need some semblance of privacy – except my windows are way too wide…. The windows are each 3 panes wide, so I am thinking maybe I can do 2 blinds per window (1/3rd, 2/3rds). I am wondering how bulky is the attaching mechanism? Do you think they would work side by side, or would there be a huge gap between them?
    Another option might be to use the rolling mechanism and custom width rods and fabric?

  • Reply Mary July 4, 2016 at 10:00 pm

    I just purchased a house that still had these roller shades. Some of the shade material has detached or shredded away from the bottom rod. I would like to cut this part away and replace bottom rod. Might you suggest how I could do this. Not sure best way to get shade back in rod.

  • Leave a Reply to Anna at D16 Cancel Reply

    Door Sixteen is a hate-free, drama-free, spam-free zone. Open dialogue is welcome, but comments designed to harm or deceive will be removed.

    This site uses Akismet to reduce spam. Learn how your comment data is processed.

    Get D16 in your mailbox

    Sign up to receive weekly digests and (occasional) other updates from Door Sixteen! I promise to not bombard your inbox.